-
Eemann Tech Sear Spring Installation Tool for CZ & TANFOGLIO
Rated 0 out of 5$43.99The Eemann Tech sear spring tool will revolutionize your sear spring installation. Either for general maintenance or because your spring broke, on the range or in your workshop, this tool will simplify a normally very tricky job and substantially reduce the time it usually takes. You can replace or install your sear spring in seconds without any experience. We recommend the installation of the Eemann Tech Competition sear spring part number 131113 or the Eemann Tech extended competition sear spring part number 131114. The new Eemann Tech sear spring tool incorporates a tiny neodeum magnet which holds the sear spring very securely whilst the short leg of the sear spring rests in a micro hole within the tool. There are special relief cuts in the tool that allow it to be positioned correctly for the instal. The tool is made of brass that is softer than the spring thus will not damage it, but it's hard enough to perform the task. Compatible with all cz 75 type pistols and their clones: • CZ 75 pistols • CZ Shadow 2 pistols • Tanfoglio pistols Material: Brass -
New Quick viewSelect options This product has multiple variants. The options may be chosen on the product page Add to wishlist Add to compare
Eeann Tech Slide Stop with Thumb Rest for CZ 75
Rated 0 out of 5$84.99 – $89.99Eemann Tech Slide Stop with rhumb rest for better recoil control. Best solution for IPSC Standard division!
The Eemann Tech slide stop with thumb rest is made from one piece of carbon steel and CNC machined to the highest standards.
Fits in IPSC Standard Box with OEM Safety. Compatible with: • CZ 75 Shadow Line • CZ 75 SP-01 ShadowAdvantages:
• No firearm modification required • No fitting required and instant installation • Provides stability and consistent grip for recoil control • Slide stop thumb rest functions as a normal slide stop allowing slide to lock back if required • When installed, fits in the IPSC Standard gun box with OEM Safety. • Legal in Standard and Open divisions • Not legal in IPSC Production division
Installation:
Remove existing slide stop and replace with Eemann Tech slide stop with thumb rest
Color: •Black
Total width: 41,5mm Thumb rest width: 11mm Weight: 13g
-
Eemann Tech Trigger Spring Tool for CZ
Rated 0 out of 5$41.99Eemann Tech trigger spring tool for CZ 75 pistols and their clones. The Eemann Tech trigger spring tool will revolutionize your trigger spring installation. Either for general maintenance or because your spring broke, on the range or in your workshop, this tool will simplify a normally tricky job and substantially reduce the time it usually takes. You can replace or install your trigger spring in one minute without any experience. We recommend the installation of the Eemann Tech Competition trigger spring ET-131109 and the competition trigger pin ET-130064. The tool is made of brass that is softer than the spring thus will not damage it, but it's hard enough to perform the task. Compatible with all cz 75 type pistols and their clones: • CZ 75 pistols • CZ Shadow 2 pistols • Tanfoglio pistols • Sphinx Pistols • Phoenix Pistols Material: Brass Total Length: 76mm Weight: 40g -
New Quick viewSelect options This product has multiple variants. The options may be chosen on the product page Add to wishlist Add to compare
Eemann Tech Slide Stop with Thumb Rest for CZ SHADOW 2 & Shadow 2 Compact
Rated 0 out of 5$84.99 – $86.99The Eemann Tech slide stop with thumb rest is made from one piece of carbon steel and CNC machined to the highest standards.
Best solution for IPSC Standard division.
Fits in IPSC Standard Box with OEM Safety.
Compatible with: • CZ Shadow 2 • CZ 75 Tactical Sports • CZ Shadow 2 COMPACT -
Eemann Tech HQ “Stainless Steel” Competition Thumb Safety with Shields for 1911/2011
Rated 0 out of 5$149.99Eemann Tech Competition Ambidextrous Thumb Safety with Shield for 1911/2011 -
Eemann Tech Extended Firing Pin for 1911/2011
Rated 0 out of 5$26.99The EXTENDED Firing Pin for Colt 1911, 2011 and their clones. Extended Firing Pin resolve the misfire faults caused by weak main or firing pin springs. Total length: 2,296" (59mm) Material: Stainless Steel / Steel Caliber: 9x19mm; .38super; .40S&W All the EEMANN TECH parts for Colt 1911, STI 2011 and their clones are made from high quality carbon, alloyed or stainless steel using technologies and CNC machines of new generation. -
New Quick viewSelect options This product has multiple variants. The options may be chosen on the product page Add to wishlist Add to compare
Eemann Tech Progressive Recoil Spring for 1911/2011
Rated 0 out of 5$18.99The Eemann Tech Progressive Recoil Spring for 1911/2011 pistols and their clones with 5" barrel length. Available in different power. -
Eemann Tech Recoil Springs Calibration Pack Open Major for 1911/2011
Rated 0 out of 5$39.99Eemann Tech Recoil Springs Calibration Pack "OPEN MAJOR" for 1911/2011 pistols and their clones with 5" barrel length. Calibration Pack "OPEN MAJOR" contains Progressive Recoil Springs from 6 lbs. till 9 lbs. - mostly used in "OPEN (MAJOR)" 1911/2011 pistols classified by IPSC rules. “OPEN MAJOR” pack contains: • ET-131126 / 6 lbs - 1 pc. • ET-131127 / 7 lbs - 1 pc. • ET-131128 / 8 lbs - 1 pc. • ET-131129 / 9 lbs - 1 pc. Progressive Recoil Spring differs from the common spring by the fact that the distance between coils keeps reducing starting from the middle of the spring till the last coil. While getting pressure the spring starts functioning in two phases: • 1st: The first half of the spring with identical distance between coils starts compressing from the beginning. • 2nd: After the first half has been fully shrunk the second half with reduced coil distance starts its compressing as well. Each coil increases the spring compression. Full compression provides maximum resistance and reduces recoil impulse. Every Eemann Tech Recoil spring has its own unique color that allows visual identifying the power value throughout its whole service life period. All springs painted in polymer heat treated paint which remains flexible throughout the whole period of service. The paint does not ruin or dye handgun from inside. Note: • Installation of the progressive recoil spring for 1911/2011 by certified gunsmith is recommended. -
New Quick viewSelect options This product has multiple variants. The options may be chosen on the product page Add to wishlist Add to compare
Eemann Tech Ultra Light Competition Hammer for 1911/2011
Rated 0 out of 5$69.99 – $89.00Eemann Tech Ultra Light Competition Hammer for Colt 1911, STI 2011 and clones. Material: Alloy Steel Caliber: All Catalog number: 40 Hammer weight: 11g All the EEMANN TECH parts for Colt 1911, STI 2011 and their clones are made from high quality carbon, alloyed or stainless steel using technologies and CNC machines of new generation. -
Eemann Tech Sear Spring for 1911/2011
Rated 0 out of 5$31.99Eemann Tech Sear Spring for Colt 1911, STI 2011 and clones. Material: Steel Caliber: All All the EEMANN TECH parts for Colt 1911, STI 2011 and their clones are made from high quality carbon, alloyed or stainless steel using technologies and CNC machines of new generation. -
New Quick viewSelect options This product has multiple variants. The options may be chosen on the product page Add to wishlist Add to compare
Eemann Tech Main Spring for 1911/2011
Rated 0 out of 5$16.99Eemann Tech Main Spring for Colt 1911, STI 2011 and clones. Available in different power. 14, 15, 16, 17, 18 Lbs. Material: Steel Caliber: All All the EEMANN TECH parts for Colt 1911, STI 2011 and their clones are made from high quality carbon, alloyed or stainless steel using technologies and CNC machines of new generation. -
Eemann Tech Recoil Springs Calibration Pack “CLASSIC MAJOR” for 1911/2011
Rated 0 out of 5$39.99Eemann Tech Recoil Springs Calibration Pack "CLASSIC MAJOR" for 1911/2011 pistols and their clones with 5" barrel length. -
Eemann Tech Competition Extractor for 1911/2011
Rated 0 out of 5$107.99The Eemann Tech Competition Extractor for 1911/2011 Pistol models and clones. -
New Quick viewSelect options This product has multiple variants. The options may be chosen on the product page Add to wishlist Add to compare
Eemann Tech Slide Stop with Thumb Rest for 1911/2011
Rated 0 out of 5$129.99The Eemann Tech slide stop with thumb rest is made from one piece of carbon steel and CNC machined to the highest standards. It is designed to be used with 1911/2011 firearms and their clones. This is not drop-in part! Installation only by certified gunsmith recommended! In some cases, pistols may differ in production or pre-modified and may require assistance of certified gunsmith for installation.